分析硅膠點膠機對封裝環境有什么要求？
有機硅點膠機對包裝環境的要求是什么?比產品的質量好，不僅僅是產品本身的性能。它還受到外部因素的影響。以硅膠、膠水為例，膠水的質量和機器本身的性能特點，同時膠水的比例合適，液體的粘稠度，以及包裝環境的影響，都會有進一步的解讀。
What are the requirements of silicone dispenser for packaging environment? It is better than the quality of the product, not only the performance of the product itself. It is also influenced by external factors. Taking silica gel and glue as examples, the quality of glue and the performance characteristics of the machine itself, as well as the proper proportion of glue, the viscosity of liquid, and the impact of packaging environment, will be further interpreted.
當然，這些因素是可以控制的。探討了包裝環境對膠水質量的影響。
Of course, these factors can be controlled. The influence of packaging environment on glue quality was discussed.
在有機硅點膠機的應用過程中，通常采用消去法。檢查硅膠點膠機是否正常工作，然后檢查膠水。之后，我們會檢查包裝環境。影響包裝環境的主要因素有兩個:電源和空間。
In the application of silicone dispenser, elimination method is usually used. First, check whether the silicone dispenser works normally, and then check the glue. After that, we will check the packing environment. There are two main factors affecting the packaging environment: power supply and space.
讓我們從電源問題開始。硅配藥功率必須穩定，電壓穩定。在封裝過程中，電源波動頻繁，可以通過隔離穩壓電源來解決。
Let's start with the power problem. The power and voltage of silicon dosing must be stable. In the packaging process, the power supply fluctuates frequently, which can be solved by isolating the regulated power supply.
此外，一些高頻干擾也會影響流體封裝的質量。有經驗的操作人員常使用硅膠點膠機的電容過濾法。這些都是由電源故障引起的，以減少包裝環境的故障。
In addition, some high-frequency interference will also affect the quality of fluid packaging. Experienced operators often use the capacitance filtration method of silica gel dispenser. These are caused by power failure to reduce the failure of the packaging environment.
除電源問題外，硅膠點膠機還會受到空間因素的干擾。如果硅橡膠機中的空氣是在環境中，環境中的空氣、底座的浮動、振動、氣體和空間輻射的干擾都會影響硅橡膠點膠機的運行。而空間干擾的問題比停電更難解決，因為它無法用儀器準確測量，不穩定性很強，所以需要的硅膠機技術人員進行檢查、分析和維護。
In addition to the problem of power supply, the silicone dispenser will also be disturbed by space factors. If the air in the silicone rubber dispenser is in the environment, the air in the environment, the floating of the base, the vibration, the interference of air and space radiation will affect the operation of the silicone rubber dispenser. The problem of space interference is more difficult to solve than power failure, because it can not be accurately measured by instruments and has strong instability, so it needs professional silica gel machine technicians to check, analyze and maintain.
上一篇：玻璃清洗機的風干系統是如何工作的?
下一篇：雙組份打膠機?主要技術參數是什么？
